[Flexradio] [Advertising]: Ham Radio Deluxe loses connection with PowerSDR

[Michael Walker (VA3MW)]

I've used this with HRD on Vista 64 with no problem.

I had Writelog connected to HRD's virtual Kenwood port.  It is free.

http://com0com.sourceforge.net/.

Mike VA3MW


http://walkerphoto.blogspot.com/2009/07/remote-ham-radio-operating.html

-----Original Message-----
From: Neal Campbell [mailto:nealk3nc at gmail.com] 
Sent: Sunday, September 06, 2009 08:30
To: Stu Phillips
Cc: flexradio at flex-radio.biz
Subject: [Flexradio] [Advertising]: Ham Radio Deluxe loses connection with
PowerSDR

You can order a lite version of Eltima's VSPD that allows definition of 2
comm port pairs from my website .

http://www.abrohamnealsoftware.com/proddetail.php?prod=vspdlite50

Its half the price of the unlimited version.

73

Neal Campbell
Abroham Neal Software
www.dxbase.com
www.abrohamnealsoftware.com
www.sdrsystems.com
(540) 242 0911

Amateur Radio: K3NC
Blog: http://www.abrohamnealsoftware.com/blog/
DXBase bug reports: email to cases at dxbase.fogbugz.com
Abroham Neal forums: http:/www.abrohamnealsoftware.com/community/

DX Cluster: dxc.k3nc.com port 23





On Sun, Sep 6, 2009 at 8:21 PM, Stu Phillips <stu at ridgelift.com> wrote:

> Jim,
>
> I had the same problem until I swithed to the Eltima virtual drivers.
> Since then I've had zero problems with any of the virtual serial ports.
> I'm also using Vista X64.
>
> You can download the trial version of the Eltima drivers from their web
> site - fully functional for 14 days.
>
> Worth the money IMO.
>
> 73
> Stu K6TU
>
> -----Original Message-----
> From: flexradio-bounces at flex-radio.biz
> [mailto:flexradio-bounces at flex-radio.biz] On Behalf Of Jim
> Sent: Sunday, September 06, 2009 5:19 PM
> To: flexradio at flex-radio.biz
> Subject: [Flexradio] Ham Radio Deluxe loses connection with PowerSDR
>
> I'm running HRD and PowerSDR on a Dell Inspiron 530 with 8GB of RAM and
> Vista 64 bit.
>
> I'm using com0com for the virtual com port connections and I have
> emulate
> baud rate and enable buffer overrun selected. The baud rate in PowerSDR
> for
> the com ports is set to 57600
>
>
>
> If I Launch HRD it works just fine but then after a few minutes the
> connection is lost and an error pops up that says "The connection with
> TS-2000 on COM6 has stopped working".
>
>
>
> Where do you think the problem lies? Is it an HRD defect, a PowerSDR
> defect,
> a Com0Com defect, or?
>
>
>
> Thanks very much
>
> Jim
>
> WD7W
>
>
>
>
>
>
>
> _______________________________________________
> FlexRadio Systems Mailing List
> FlexRadio at flex-radio.biz
> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
> Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
> Knowledge Base: http://kc.flex-radio.com/  Homepage:
> http://www.flex-radio.com/
> Message delivered to stu at ridgelift.com
>
> _______________________________________________
> FlexRadio Systems Mailing List
> FlexRadio at flex-radio.biz
> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
> Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
> Knowledge Base: http://kc.flex-radio.com/  Homepage:
> http://www.flex-radio.com/
> Message delivered to nealk3nc at gmail.com
>
_______________________________________________
FlexRadio Systems Mailing List
FlexRadio at flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage:
http://www.flex-radio.com/
Message delivered to va3mw at portcredit.net