[Flexradio] no power out 6 m zero watts

[Dudley Hurry]

Carl,

The bridge in the 5K is calibrated with the ATU physically out of the 
circuit.. There is some effect of the ATU physically connected at 6.   
Make sure that you dummy load is good (good 50 ohm load )  at six 
meters..   Some watt meters and antennas loads will not indicate 
reliably on 6 meters. 

73,
Dudley

WA5QPZ



N4PY2 wrote:
> My Flex 5000 reads 75 watts on 6 meters.
>
> Carl Moreschi N4PY
> 121 Little Bell Drive
> Hays, NC 28635
> www.n4py.com
>
>
> ----- Original Message ----- From: <k6xr at bak.rr.com>
> To: <flexradio at flex-radio.biz>; "Ed Stallman" <n5dg at airmail.net>; "Tim 
> Ellison" <tellison at itsco.com>
> Sent: Friday, December 04, 2009 6:00 PM
> Subject: Re: [Flexradio] no power out 6 m zero watts
>
>
>> What should be the power out on 6m? I have always got about 36 watts 
>> out max on 6 and another friend with a 3000 also get about the same.
>>
>> Reggie k6xr
>>
>>
>>
>>
>>
>>
>>
>> ---- Tim Ellison <tellison at itsco.com> wrote:
>>> You have done everything correctly.  Contact Dudley directly at 
>>> FlexRadio support (support at flex-radio.com) so he can triage the 
>>> problem with 6m.
>>>
>>>
>>>
>>> -Tim
>>>
>>> -----Original Message-----
>>> From: flexradio-bounces at flex-radio.biz 
>>> [mailto:flexradio-bounces at flex-radio.biz] On Behalf Of Ed Stallman
>>> Sent: Friday, December 04, 2009 5:27 PM
>>> To: flexradio at flex-radio.biz
>>> Subject: [Flexradio] no power out 6 m zero watts
>>>
>>> This happened when I updated SVN PB-Pal , My power on the HF bands 
>>> went to 150 watts . I did the Ctrl Shift F to calibrate the power, 
>>> all calibrated fine until it got to 6m . At that point PSDR would 
>>> stop and shut down.
>>>
>>> Reading the mail on the reflector, I read were all calibrating 
>>> need's to be done using the official release. Today I installed 
>>> Drivers,Firmware and PSDR from the Flex web page (front page) Doing 
>>> the power calibrate, all HF bands did fine, This time when it got to 
>>> 6m, it did not shut down PSDR ... It just sat there and did nothing, 
>>> I could see a wave form in the filter bandwidth and the Mox tab was 
>>> highlighted . I Gave it may be 5 minutes before clicking X and stop 
>>> on PSDR
>>>
>>> I tried this with 2 different OS, windows XP home and Windows 7 32 
>>> bit. their was no change with either,
>>>
>>> So were did my 100 watts go on 6m ?
>>>
>>> Yes I was in 96k and 1024
>>>
>>> Yes I used a dummy load on port one
>>>
>>> yes it was a new data base
>>>
>>> Radio Flex 5000a
>>>
>>> Thanks for any help , Ed
>>>
>>>
>>> _______________________________________________
>>> FlexRadio Systems Mailing List
>>> FlexRadio at flex-radio.biz
>>> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
>>> Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
>>> Knowledge Base: http://kc.flex-radio.com/  Homepage: 
>>> http://www.flex-radio.com/ Message delivered to tellison at itsco.com
>>>
>>> _______________________________________________
>>> FlexRadio Systems Mailing List
>>> FlexRadio at flex-radio.biz
>>> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
>>> Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
>>> Knowledge Base: http://kc.flex-radio.com/  Homepage: 
>>> http://www.flex-radio.com/
>>> Message delivered to k6xr at bak.rr.com
>>
>>
>> _______________________________________________
>> FlexRadio Systems Mailing List
>> FlexRadio at flex-radio.biz
>> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
>> Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
>> Knowledge Base: http://kc.flex-radio.com/  Homepage: 
>> http://www.flex-radio.com/
>> Message delivered to n4py2 at earthlink.net 
>
>
> _______________________________________________
> FlexRadio Systems Mailing List
> FlexRadio at flex-radio.biz
> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
> Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
> Knowledge Base: http://kc.flex-radio.com/  Homepage: 
> http://www.flex-radio.com/
> Message delivered to jhurry at austin.rr.com
>